Wasatch Quad Plus 4-Port Ethernet Controller with Power Distribution and a 4-Port Differential Connection that both run on WLED and can receive light show data from xLights
This is an ESP32-based dual Ethernet and WiFi controller to control 4 LED pixel strings and/or strips directly plus 4 LED pixel strings and/or strips remotely via a differential connection and an additional differential receiver. This controller has built-in power distribution with standard Phoenix connectors for convenience in hooking up your LED strings or strips.
For 5V pixels select the 5V version. For 12V pixels, select the 12V version. The data signal sent to a remote differential receiver can be sent to either 5V or 12V pixels depending on how your differential receiver is configured.
What is it?
This is a controller for WS2812, WS2811, WS2815 and various other protocol LED pixels. It uses an ESP32-based WT32-ETH01 board with a custom HAT that shifts the 3.3V signals from the ESP32 to 5V signals expected by strings and strips of LEDs. It comes pre-installed with WLED software that supports both Ethernet and WiFi connectivity. This can be used to control colors and effects on LED lights via WLED and its companion Android and iOS apps. It also receives live E1.31 and DDP data for sequenced light shows from programs such as Vixen and xLights and Falcon Player — FPP — (no paid license needed). This board has 4 onboard outputs to control and power 4 separate light strings as well as 4 additional differential outputs to control LED pixels up to 300′ away connected to a differential receiver. The differential receiver can be any differential receiver that works in normal mode such as Falcon, Kulp, and Experience Lights. Wasatch Pixels also offers a differential receiver for purchase that will work with the Quad+ controller: https://wasatchpixels.com/product/wasatch-pixels-normal-differential-receiver/
What makes it special?
This is an Ethernet pixel controller that runs WLED and supports high frame rate pixels shows. Unlike dig-uno and dig-quad boards, it has Ethernet built in without extra cost and can support high frame rates without lagging or staggering. It has 4 onboard outputs along with 4 differential outputs so you can control up to 8 separate strings of LED lights. The 4 differential output signal is sent via an Ethernet cable to another differential receiver up to 300 feet away. This is the only pixel controller we know of that runs WLED natively and has a differential output.
Power Source:
This board outputs both data and power to pixels. There is no need for a separate power distribution board unless needed for power injection. Each port accommodates up to 5 amps. Select the input voltage you will be using when ordering: 5V, 12V, or 24V.
Led Pin Assignments:
– Led 1: Pin 2
– Led 2: Pin 4
– Led 3: Pin 12
– Led 4: Pin 14
– Led 5: Pin 15
– Led 6: Pin 17
– Led 7: Pin 5
– Led 8: Pin 33
Recommended maximum number of pixels per pin:
– 40 Frames Per Second: 400 pixels/port (has been tested to 600 pixels/pin)
– 20 Frames Per Second: 800 pixels/port
WLED is distributed under the MIT License
Copyright (c) 2016 Christian Schwinne
THE SOFTWARE IS PROVIDED “AS IS”, WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY,
FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE
AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER
LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM,
OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE
SOFTWARE.
Benjamin Petersen (verified owner) –
So far, so good! I can’t believe how quick it was to setup my LED lights with this board. I have spent multiple days, trying to flash esp32 and ESP8266 boards, then trying to get the right pin out for the data line. Once I figured it out, I still needed a shifter to make the data line 5v?? This device has it all in one. Wired in my powersupply, hooked up the wires from the first set of led lights, and it just worked!
I am still learning WLED, so getting the 2nd and 3rd strands of LED lights to work, that were connected to the first strand, was a bit tricky. However, I like that I can make a preset once it works, and then set it and they light up.
I am new to LED lighting and electronics, but not new to the DIY scene. This board is going to be fun!